Siemens Drawer Service Center in Malad :
Cabinet drawers usually work by sliding along a set of drawer guides. The guides, made from metal U-channel strips, accommodate rollers fastened to the sides of the drawer, allowing the drawer to open and close. As the drawer fills with more objects and is continually opened and closed, contents shift, causing one or two objects to fall out of the back of the drawer box or to stick up. This prevents the drawer from closing fully. Alternatively, the slides may be defective.
Step 1
Open the drawer as far as possible. Look in the back for any contents in the drawer box that might be sticking up or out the back of the drawer box, preventing it from completely closing. Remove anything that might prevent the drawer from closing all the way.
Step 2
Find the tab stops on either side of the drawer and push the tabs in with your thumbs. Pull out the drawer and put it on top of the counter temporarily.
Step 3
Shine a flashlight into the recess. Look for any objects near the back of the recess preventing the drawer from closing. Pull them out, if any obstructions are present.
Step 4
Unfasten the drawer slides on either side of the recess where the drawer fits using a screwdriver. Pull the drawer slides out of the recess after removing the mounting screws. Look for kinks or warping, preventing the drawer from closing. Fix or replace, as necessary.
Step 5
Hold the drawer slide against one side of the drawer recess, aligning the pre-drilled holes in the slide with the holes in the drawer recess. Fasten the slide with a screwdriver and screws. Then repeat the drawer slide installation on the opposite side.
Step 6
Insert the rollers on the sides of the drawer into the slides, aligning them, allowing the rollers to roll inside the U-channel. Push the drawer back into the recess. The drawer should now properly open and close.
Remove the drawers from the desk. Turn them on their sides. Using a small Phillips screwdriver, remove the screws that hold the runners to the drawer on both sides and remove the runners.
Sand off any dried adhesive after removing the runners, if necessary. Some manufacturers apply adhesive to help stabilize the runners and extend the life. Use an oscillating tool fitted with a hook and loop pad accessory and medium-grit sandpaper or sand it by hand.
Purchase runners of the same type and length, using one of the old runners for comparison.
Stand each drawer on its side. Place the new runner where the old one came off. The runners are marked either “L” or “R” for left and right. But don’t worry — they won’t fit unless they are on the correct side.
5
Screw the runners back onto the sides of the drawers using the new screws that come with the packaged runners.
6
Insert the drawers into the desk. If the drawers will not close tight, remove them. There are two holes in the runners that are oval shaped. Loosen these screws. Move the runner up or down and tighten the screws again.
7
Insert the drawers again. If they don’t fit tight, adjust the screws the opposite way and test again until the drawers fit.
siemens-servicecenterinmumbai.com
Are you may searching for the no.1 best best service center that can solve your issues within a seconds. Are you may worry ha about your products just contact to our service center siemens-service center in Mumbai we are providing excellent service for the customers professional and genuine service for the all types of home products.in our service center we are having 100% customers are satisfied. We are available throughout the Mumbai in our service center our technicians are highly talented and knowledge. Siemens is the one the trusted service cnter.in our service center we are repair and service installation for your home products.
Types of home appliances;
- Washing machine
- Refrigerator
- Air conditioner
- Microwave oven
About our service center;
In our service center we are providing you all excellent and genuine service for your appliances. In our service center we are 24/7 hours in online to receive your complaints and make you satisfaction by our service center. In our service center we are service you all multiple home appliances. We are having highly educated and general knowledge technicians who can solve your all types of our minor or major issues within a short period of time. In our service center there is a very less visiting charges only 350/- if any extra spare parts are adding means extra charges will be considered. In our service 100% customers got satisfaction by our service center. In our service center 100% we are having 10 yrs. experiences how to deal with customer’s issues.
Here at our service center we provide service for all models of home appliances like washing machines, refrigerators and microwave ovens. When your complaint was registered you will get a complaint number on your mobile, before reaching you our technician will call you and share your exact location to him. We respond very quickly and send our service engineer within ninety minutes to your doorstep. They provide thirty days warranty on general service and ninety days warranty on spare parts. We provide service for out of warranty products because our service center is unauthorized {private dealers}.
